DOI： 10.1039/d2py00005a

DOI： 10.1021/acsami.2c15786

DOI： 10.1021/acsami.1c09233

掲載種別：研究論文（学術雑誌）  

DOI： 10.1021/acsanm.1c00366

DOI： 10.1021/acs.macromol.0c02345

DOI： 10.1021/acs.macromol.0c00464

DOI： 10.1021/acs.macromol.0c00161

掲載種別：研究論文（学術雑誌）  

Very-thick, concentrated brushes of poly(methyl methacrylate) (PMMA) were synthesized by surface-initiated atom transfer radical polymerization in N,N-diethyl-N-methyl-N-(2-methoxyethyl)ammonium bis(trifluoromethanesulfonyl)imide, an ionic liquid (IL) solvent. Notably, the high polymerization rate in this IL produced 700 nm-thick PMMA brushes, while the grafting density was observed to increase with increasing feed concentration of a deactivator catalyst (Cu(II)Cl2/ligand), suggesting that grafting density is significantly determined by chain growth during a single activation cycle. A concentrated PMMA brush, with a number-average molecular weight of 1.28 × 106, a polydispersity index of 1.23, a brush-layer thickness of 510 nm, and a grafting density of 0.30 chains nm-2, was successfully synthesized by taking advantage of the IL effect that provides a higher propagation rate constant and a lower termination rate constant. Further increases in the brush-layer thickness were achieved by moderately pressurizing the polymerization medium (i.e., by the combined use of the IL solvent and pressure), and an approximately 1 μm-thick concentrated polymer brush was conveniently synthesized at 50 MPa.

DOI： 10.1021/acs.macromol.0c00161

掲載種別：研究論文（学術雑誌）  

Very-thick, concentrated brushes of poly(methyl methacrylate) (PMMA) were synthesized by surface-initiated atom transfer radical polymerization in N,N-diethyl-N-methyl-N-(2-methoxyethyl)ammonium bis(trifluoromethanesulfonyl)imide, an ionic liquid (IL) solvent. Notably, the high polymerization rate in this IL produced 700 nm-thick PMMA brushes, while the grafting density was observed to increase with increasing feed concentration of a deactivator catalyst (Cu(II)Cl-2/ligand), suggesting that grafting density is significantly determined by chain growth during a single activation cycle. A concentrated PMMA brush, with a number-average molecular weight of 1.28 x 10(6), a polydispersity index of 1.23, a brush-layer thickness of 510 nm, and a grafting density of 0.30 chains nm(-2), was successfully synthesized by taking advantage of the IL effect that provides a higher propagation rate constant and a lower termination rate constant. Further increases in the brush-layer thickness were achieved by moderately pressurizing the polymerization medium (i.e., by the combined use of the IL solvent and pressure), and an approximately 1 mu m-thick concentrated polymer brush was conveniently synthesized at 50 MPa.

DOI： 10.1021/acs.macromol.0c00161

DOI： 10.1016/j.triboint.2019.106130

DOI： 10.1021/acsapm.9b00839

掲載種別：研究論文（学術雑誌）  

The synthesis of ultrathick concentrated poly(methyl methacrylate) (PMMA) brushes by atom transfer radical polymerization (ATRP) was investigated. The reactions were performed with a catalyst system of Cu(I)Br/dinonyl-2,2′-bipyridine (dN-bipy) and Cu(II)Br /dN-bipy at 60 °C under a high pressure of 500 MPa. The equilibrium constant for this catalyst system was determined to be 1.5 × 10 , which followed the kinetics study and indicated good polymerization rate control. Under the high pressure of 500 MPa, a micrometer scale thick PMMA brush was obtained. During chain growth under the high pressure, the concentration of the deactivator catalyst was demonstrated to significantly affect the graft density of PMMA brushes, which was correlated to the number of monomers added in activation-deactivation cycles. A novel "cutoff" experiment and gel permeation chromatography demonstrated similar propagation for free polymers and graft polymers even under high pressure. 2 -6

DOI： 10.1021/acs.macromol.9b02072

DOI： 10.1021/acs.macromol.9b02072

掲載種別：研究論文（学術雑誌）  

The synthesis of ultrathick concentrated poly(methyl methacrylate) (PMMA) brushes by atom transfer radical polymerization (ATRP) was investigated. The reactions were performed with a catalyst system of Cu(I)Br/dinonyl-2,2'-bipyridine (dN-bipy) and Cu(II)Br-2/dN-bipy at 60 degrees C under a high pressure of 500 MPa. The equilibrium constant for this catalyst system was determined to be 1.5 x 10(-6), which followed the kinetics study and indicated good polymerization rate control. Under the high pressure of 500 MPa, a micrometer scale thick PMMA brush was obtained. During chain growth under the high pressure, the concentration of the deactivator catalyst was demonstrated to significantly affect the graft density of PMMA brushes, which was correlated to the number of monomers added in activation-deactivation cycles. A novel "cutoff" experiment and gel permeation chromatography demonstrated similar propagation for free polymers and graft polymers even under high pressure.

DOI： 10.1021/acs.macromol.9b02072

掲載種別：研究論文（学術雑誌）  

DOI： 10.1021/acs.langmuir.9b02573

DOI： 10.1021/acs.langmuir.9b01747

DOI： 10.1063/1.5091845

DOI： 10.1021/acs.macromol.9b00720

掲載種別：研究論文（学術雑誌）  

DOI： 10.1039/c8tb03228a

DOI： 10.1039/c9py00436j

掲載種別：研究論文（学術雑誌）  

DOI： 10.1002/chem.201805121

掲載種別：研究論文（学術雑誌）  

DOI： 10.1021/acs.langmuir.8b03891